Wood Flooring

Go Back
Amighini Engineered Wood Flooring

Amighini Engineered wood floors - How are they made?



Our engineered wood floors are built having 3-12 multiple ply layers (see picture below) that are cross layered, glued and pressed together. The inner core layers are are generally built up with either a hardwood and/or soft plywood type of material, which incorporates the tongue and groove system. The top thicker hardwood veneer wear layer is then glued and pressed on the top surface of the core. Engineered hardwood flooring is available in almost any wood species.

The benefits of using Our engineered wood floors include more resistance to higher moisture levels than solid wood flooring, which adds to their appeal to use in damp basements or in regions of the country that have higher relative humidity levels. Also, engineered flooring (excluding the newer Click Lock flooring) can be direct glued-down over (dry) concrete slabs above or below grade or stapled down over a wood subfloor.

Our Engineered Hardwood floors range in widths from 3-9 inches wide and in thicknesses from 3/8 - 3/4" they also come in a wide variety of domestic and exotic hardwood species and some are even available in the popular hand scraped styles. Some brands of engineered flooring have a thin .6 mm wear layer that can only be re-coated and cannot be sanded and refinished new again once they get worn. They have an average lifespan of between 20-30 years depending on traffic. AMIGHINI wooden floors have a thicker 4 - 8 mm thick wear layer that can be completely sanded and refinished 1- 5 times if they ever needed to be. These thicker wear layer engineered floors can last from 40 - 80 years before having to be replaced which add to their appeal.
Engineered wood floors are manufactured two ways, one, where the top surface wear layer is Sliced/Sawn cut from the log like solid wood flooring is. Engineered hardwood flooring that has a Sliced/Sawn cut wear layer shows the truer natural look of the wood and finer graining. Sliced/Sawn cut engineered flooring also allows a thicker wear layer. Engineered wood floors can also be Rotary cut, which the veneer hardwood wear layer is peeled off the log using big lathes. This peeling method can show dramatic wilder graining.

Not all engineered flooring are alike!
Some homeowners think that engineered flooring is not as good as solid 3/4 IN. thick flooring because they are under the impression that it’s cheaply made. Well, as with all consumer products, manufacturers do make products at all levels of quality, each to fit a certain price point within the market. There are engineered floors on the cheaper end of the spectrum that are specifically manufactured to be affordable to a certain portion of the market. Sometimes, consumers are fooled into believing that these cheaper products are a bargain, but we would like to refute this belief.

AMIGHINI wood floors are a very high end engineered floors that have an incredibly thick real wood wear layer that can, later on if ever needed, be sanded and refinished. You can find in the flooring industry two different types of quality engineered flooring, and they are often intermingled by retailers and the differences between them are either not known or is not often fully explained to the consumer. As a direct result of these missteps, in lots of cases the customer will purchase the cheaper floor that they see as a great bargain, only to have it fail once it’s installed in the home. At that point, an opinion is created and the consumer starts to think that all engineered flooring is of lesser quality than solid flooring. Even if your budget is tight, it is still possible to find a good quality engineered floor, if you know what to look for. The goal of this article is to help our consumers understand the differences between a low quality engineered floor and a AMIGHINI engineered floor and, ultimately, what to look for in the specifications of an engineered floor when shopping around.

All about the wear layer
When working with a standard 3/4 IN. thick solid floor, the sandable (or renewable) wear layer is approximately 5/16 IN. If you sand down a solid floor below this depth, you will start to expose the nails that were used to install it. Therefore, the maximum wear thickness on a 3/4 IN. solid floor is going to be 5/16 IN. You can sand and refinish 3/4 IN. thick flooring approximately 5-7 times over the lifetime of the floor. The average lifespan of 3/4 IN. thick solid wood flooring is approx 100 years. With engineered flooring, wear layer thicknesses can vary greatly. Wear layers on our engineered flooring can range anywhere from 4mm to 8mm. As an example, an engineered wood floor with a wear layer of 4mm (5/32 IN.) usually can be sanded and refinished 4-5 times over the lifetime of the floor. The average lifespan of an engineered floor with this 4mm wear layer is approximately 60-80 years.

What should your concerns be?
Your concern should be what your demands are going to be for that flooring and match those demands to the flooring as best you can. If the area that the new flooring is going to be installed is it going to receive a lot of rough traffic with little or no care or maintenance then you will want a engineered floor that has a thick wear layer that can be sanded and refinished new again later if it ever needed to be. If the area is not going to be heavily trafficked and will be maintained properly then you may not need as thick a wear layer. Quality Engineered floors are very durable and are commonly used in shopping malls which receive a lot of foot traffic.
Engineered wood flooring is GreenPurchasing engineered wood flooring helps conserve expensive prized wood. For every 1 sq foot of 3/4 inch thick solid wood flooring manufactured you can manufacturer approx 4 times that amount into engineered wood flooring. Engineered wood flooring is the best flooring to provide people with to conserve our forests.

Engineered Hardwood Flooring Reviews:

Q. What's the advantage of using an AMIGHINI Engineered wood floor over a Solid nail down floor?.
A. Our Engineered hardwood floors can be installed in areas where there is slightly higher relative humidity levels. Engineered wood flooring being more stable is a great choice to use in summer homes where the heat is turned lower when no one is there. Because manufacturing engineered flooring does not waste valuable prized wood below its wear layer purchasing engineered flooring also helps conserve our forests.

Q. Does it matter what size width board or color to use? Is one width better than another?
A. No. I would suggest using whatever width board you prefer aesthetically. The rule of thumb is that a narrower board will give you a more formal look and feel to your home. A wider board (over 4 inches wide), will give you a more Country look and feel.
Floor Color is a personal choice that would have more to do with your personal tastes and decor. A natural light colored wood floor will go with any décor and will lighten up any room. I usually suggest not using dark colored flooring if your room decor is very dark.

Q. Can I use a AMIGHINI Engineered wood floor in my basement?
A. Yes, as long as the moisture content of the concrete does not exceed 4%. Basements are known to have higher relative humidity due to being under the ground. It is recommended to use a Floating engineered wood floor which allows the use of a 4-6-mil plastic vapor barrier in any areas where there is a slightly higher moisture conditions.

Q. Can I install a AMIGHINI Engineered floor over other floor coverings such as vinyl or tile?
A. Yes, as long as the other flooring is a hard surface, secured well and is flat. You cannot install any wood flooring over carpet.

Q. Can I glue down an AMIGHINI Engineered wood floor over my concrete slab that is on grade?
A. Yes, you should make certain that your slab is dry and that the moisture content does not exceed 4%. Again, depending on your particular situation we may recommend using a floating engineered floor.

Q. Are all Brands of Engineered floors the same?
A. No, like anything else you purchase there can be big differences in quality. Some manufacturers use a lower quality wood along with low grade, cheaper bonding glues for their ply layers. Their milling could also be off and their finish quality could be poor. We generally suggest to do business with Companies established at least 10 years in the industry, like AMIGHINI doing business since 1945. They will be the ones who will generally stand behind their products if something should go wrong.

Q. How much flooring do I need to order? Why do I have to add 5% to my square footage?
A. We provide easy to follow instructions as to how to measure your rooms, see our Estimator Tool. It is important to remember that all manufacturers recommend adding 5% to your actual square footage. This added 5% is recommended to cover boards that you may not want to use, that may have gotten by the inspection process at the factory and for cutting and fitting waste. If you want to run the flooring at a 45-degree angle in the room then you would want to add approx. 15% for a waste factor for the added cutting waste.

Q. What tools am I going to need to install an AMIGHINI Engineered wood floor?
A. Some flooring styles may require more or less tools that are mentioned here but generally you will need some small basic tools such as, a Combination Square, Miter saw, Hammer, Jig saw, small table saw, a pull bar, a few packages of small wood shims and a tapping block. For Staple down styles or installation method you would need a pneumatic stapler.

Q. Are there different styles of AMIGHINI Engineered flooring?
A. Yes, aside from their smooth surface styles we also produce character or hand scraped versions that are available, which would show more light and dark boards along with more pronounced character -- with the possibility of small pinholes and knots. What is extremely popular is our rustic or hand scraped look….stunning.

Q. What are the benefits of using Prefinished flooring rather than Unfinished flooring?
A. Purchasing prefinished flooring eliminates the time consuming chore of the sanding and refinishing and gives you the added benefit of a perfect finish all done for you at the factory. Most of the brand name manufacturers carry a variety of stained colors to choose from and are coated with a durable 7-10 coats of the Aluminum oxide finish, which is far more durable for wear than anything that can be purchased in a hardware store, or home center. Using prefinished flooring allows you to move right back into the room after installation. No waiting for days while the finish is being applied and drying!

All wood floors will react to the presence of moisture. In the dry winter heating months, moisture leaves the wood causing the floor to contract, which can leave unsightly gaps between each plank. In the summer months when the humidity is higher the wood will expand and the gaps will disappear. If there is too much moisture it may cause the wood planks to cup, or buckle. This is why it is important when installing a wood floor to and to acclimate the wood prior to installation and leave the proper expansion area around the perimeter. It is also important to keep the relative humidity at between 30 - 65% with all engineered flooring.

Review on the benefits of buying an engineered wood floor:

  1. The best engineered floors have a Lifespan anywhere from 30 - 100 years.
  2. Using an engineered wood floor allows you to have a wood floor on any grade level.
  3. Engineered hardwood flooring can be used on wood subfloors or dry concrete slabs.
  4. Better suited for humid areas of the country.
  5. Engineered floors are very easy and fast to install.
  6. Engineered wood floors are more dimensionally stable than solid wood floors.
  7. Engineered floors are available in many different sizes, colors and styles.
  8. Some of the best engineered floors can be sanded and refinished if ever needed.
  9. Hardwood flooring is the only floor covering that increases the value of your home.
  10. Hardwood flooring does not cause allergies, recommended to use by allergists.